ReillyBrogan - Yes, it shows broadcom-sta-current is installed.
sudo eopkg info broadcom-sta-current
Installed package:
Name : broadcom-sta-current, version: 6.30.223.271, release: 337
Summary : broadcom-sta for linux-current kernel
Description : Broadcoms IEEE 802.11a/b/g/n hybrid Linux device driver
Licenses : Distributable
Component : kernel.drivers
Dependencies : broadcom-sta-common
Distribution : Solus, Dist. Release: 1
Architecture : x86_64, Installed Size: 1.97 MB
Reverse Dependencies:

Package found in Solus repository:
Name : broadcom-sta-current, version: 6.30.223.271, release: 337
Summary : broadcom-sta for linux-current kernel
Description : Broadcoms IEEE 802.11a/b/g/n hybrid Linux device driver
Licenses : Distributable
Component : kernel.drivers
Dependencies : broadcom-sta-common
Distribution : Solus, Dist. Release: 1
Architecture : x86_64, Installed Size: 1.97 MB, Package Size: 1.97 MB
Reverse Dependencies:

      tonyk Hmm that is the right version. Can I see ls /lib/modules/6.0.9-222.current/kernel/drivers/net/wireless/ ? Also eopkg info kmod

          I am having the same issue as https://dev.getsol.us/T9962 with 6.0.9. At least, does not show luks prompt, did not investigate much further yet. Still boots with the old kernel.

          • siru replied to this.

            ReillyBrogan
            Here are the mistakes

            [ 0.128477] Spectre V2 : WARNING: Unprivileged eBPF is enabled with eIBRS on, data leaks possible via Spectre v2 BHB attacks!

            [ 1.594029] pcieport 0000:00:1c.0: pciehp: Cannot get irq -1 for the hotplug controller
            [ 1.594030] pcieport 0000:00:1c.0: pciehp: Notification initialization failed (-1)

              ReillyBrogan
              ls /lib/modules/6.0.9-222.current/kernel/drivers/net/wireless/
              admtek intel mediatek rndis_wlan.ko.zst zydas
              ath intersil ralink st
              atmel mac80211_hwsim.ko.zst ray_cs.ko.zst wl3501_cs.ko.zst
              broadcom marvell realtek wl.ko.zst

              eopkg info kmod
              Installed package:
              Name : kmod, version: 30, release: 12
              Summary : Linux kernel module management utilities
              Description : Linux kernel module management utilities
              Licenses : LGPL-2.1-or-later, GPL-2.0-or-later
              Component : system.base
              Dependencies : xz zstd glibc zlib
              Distribution : Solus, Dist. Release: 1
              Architecture : x86_64, Installed Size: 262.00 KB
              Reverse Dependencies: linux-driver-management libblockdev

              Package found in Solus repository:
              Name : kmod, version: 30, release: 12
              Summary : Linux kernel module management utilities
              Description : Linux kernel module management utilities
              Licenses : LGPL-2.1-or-later, GPL-2.0-or-later
              Component : system.base
              Dependencies : xz zstd glibc zlib
              Distribution : Solus, Dist. Release: 1
              Architecture : x86_64, Installed Size: 262.00 KB, Package Size: 84.00 KB
              Reverse Dependencies: intel-gpu-tools linux-driver-management dracut kmod-devel
              libblockdev kmod-dbginfo

              I don't see any wireless errors in dmesg.

              Thank you.

                  The required module is no longer included in kernel 6.0.9:

                  sudo zcat /proc/config.gz | grep _FB_SIMPLE
# CONFIG_FB_SIMPLE is n

                  I am still using the Nvidia driver:

                  nvidia-390-glx-driver-modaliases            - These files are used by the Software Center for hardware detection
nvidia-470-glx-driver-modaliases            - These files are used by the Software Center for hardware detection
nvidia-docker                               - nvidia-docker CLI wrapper
nvidia-glx-driver-32bit                     - 32-bit libraries for NVIDIA Binary Driver
nvidia-glx-driver-common                    - Shared assets for the NVIDIA GLX Driver
nvidia-glx-driver-current                   - NVIDIA Binary Driver (Current Kernel)
nvidia-glx-driver-modaliases                - These files are used by the Software Center for hardware detection

                  Let me know if I should raise a ticket at the development tracker.

                  darkness

                  I think I have a similar issue. After upgrading (to Linux-current 6.0) FDE prompt is not showing -- no boot is happening. I tried the following:

                  • https://getsol.us/articles/troubleshooting/boot-rescue/en/ -- no broken packages
                  • Install on a spare SSD -- after upgrade same issue
                  • Upgrade went well on a Thinkpad laptop (with FDE) and a NUC (no FDE)
                  • Tried to boot the workstation with the NUC SSD -> worked well
                  • Tried to downgrade via sudo eopkg history -t #before upgrade to Linux-current 6.0 -- did not work

                  The issue seems to be with FDE (luks/cryptsetup)

                  Host: Z170XP-SLI
                  CPU: Intel i7-7700K (8) @ 4.500GHz
                  GPU: NVIDIA GeForce GTX 1080

                      Thank you.
                      Updated today to 6.0.9 on a System76 Thelio and all is working well.

                      brent thanks for your hard work ReillyBrogan and crew....no hiccups, smooth update for Budgie.

                      That's for sure. Smooth and hiccup-free for Budgie, GNOME, MATE and Plasma here as well. Four laptops, three desktops, and four VMs with Solus editions updated. Sure gotta love this distro!

                          WetGeek I thought we'd be kicking the tires on a 5.15/5.16 variant for a few more months so this is great news---kinda paves the way for a new .iso I'd have to think.

                              WetGeek Rumor has it there are FOUR new .ISO files in our future

                              I've heard this echoed in a couple of places - where is this coming from? I don't recall any discussion on IRC about updating the ISO.

                                  • [deleted]

                                  • Post #29

                                  WetGeek So full install, minimal, netinstall and server 😉

                                      [deleted] You know, a headless version wouldn't be a bad idea. It would be a good way around having dated packages bork installs like with the current issue with some Nvidia cards. That way a person could just install, update from CLI, then install the DE of their choice.